Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Arduino Uno not taking code
Goto page Previous  1, 2
 
Post new topic   Reply to topic    www.mcselec.com Forum Index -> BASCOM-ARDUINO
View previous topic :: View next topic  
Author Message
Neptune769

Bascom Member



Joined: 27 Jul 2008
Posts: 55

usa.gif
PostPosted: Wed May 04, 2016 9:40 pm    Post subject: Reply with quote

Paulvk wrote:
Hello Neptune769

No not that screen
The bascom program chip screen (F4) on key board

Regards Paul


Sorry, I misunderstood. When the window first opens after pressing F4 it doesn't show the chip but after a few seconds it does.
Back to top
View user's profile
Neptune769

Bascom Member



Joined: 27 Jul 2008
Posts: 55

usa.gif
PostPosted: Wed May 04, 2016 11:02 pm    Post subject: Reply with quote

Duval JP wrote:
I dont understand because this programm works with Win XP, WIN7, win10
did you look where your arduino is connected : com?
JP Question


I don't understand it either. Sad Now you know why I'm asking for help. Anyway. Yes it's on the right com port. Because when I try to upload the code to the Arduino the TX/RX leds flash. I have tried three Arduino Uno boards, I also removed the chip and put a 4th chip on. Then I changed the code for my mega and tried that. All have the same results.
Back to top
View user's profile
Duval JP

Bascom Member



Joined: 22 Jun 2004
Posts: 827
Location: France

france.gif
PostPosted: Mon May 09, 2016 9:06 am    Post subject: Reply with quote

Of course, for the mega you change also the programmer, it is not Arduno but Arduino STK500 V2

Also, one time, I don't understand why, my uno stop of working, same symptom as you have, I change the M328 , same.

I checked with Arduino IDE it was working...

I change of computer, it was working with bascom too...I stop and restart the previus computer and now it is ok.


Please don't be worry, we must know why you have a problem, and we must solve it. that is the forum challenge !

JP
Back to top
View user's profile Visit poster's website
EDC

Bascom Expert



Joined: 26 Mar 2014
Posts: 589

poland.gif
PostPosted: Mon May 09, 2016 10:22 am    Post subject: Reply with quote

My working settings for Arduino Nano with Atmega328P (see picture)
Back to top
View user's profile Visit poster's website
Neptune769

Bascom Member



Joined: 27 Jul 2008
Posts: 55

usa.gif
PostPosted: Mon May 09, 2016 10:29 pm    Post subject: Reply with quote

Thank you Duval & EDC. I'll keep trying things.
Back to top
View user's profile
aphawk

Bascom Member



Joined: 23 Jan 2010
Posts: 151
Location: Brazil

brazil.gif
PostPosted: Tue May 10, 2016 2:46 am    Post subject: Reply with quote

This is my config for Arduino Uno R3 , the Parameter command is long, then follows in separate :

Parameter : -v -F -C c:\arduino\hardware\tools\avr\etc\avrdude.conf -p m328p -P com7 -c arduino -b 115200 -Uflash:w:{FILE}:a

Paulo
Back to top
View user's profile
EDC

Bascom Expert



Joined: 26 Mar 2014
Posts: 589

poland.gif
PostPosted: Sat May 28, 2016 1:05 pm    Post subject: Reply with quote

Tested with Mega2560
Back to top
View user's profile Visit poster's website
Paulvk

Bascom Member



Joined: 28 Jul 2006
Posts: 1107
Location: SYDNEY

australia.gif
PostPosted: Tue May 31, 2016 1:59 pm    Post subject: Reply with quote

I found this program just two days ago
it loads the HEX file into the Arduino
http://russemotto.com/xloader/

If you load the nano file from here with it http://www.mcselec.com/index2.php?option=com_forum&Itemid=59&page=viewtopic&t=13341&start=15
the led on the board should blink

Regards Paul
Back to top
View user's profile
Neptune769

Bascom Member



Joined: 27 Jul 2008
Posts: 55

usa.gif
PostPosted: Tue May 31, 2016 10:35 pm    Post subject: Reply with quote

Paulvk wrote:
I found this program just two days ago
it loads the HEX file into the Arduino
http://russemotto.com/xloader/

If you load the nano file from here with it http://www.mcselec.com/index2.php?option=com_forum&Itemid=59&page=viewtopic&t=13341&start=15
the led on the board should blink

Regards Paul


Than you Paul I'll give it a try when I get a chance.
Back to top
View user's profile
Display posts from previous:   
Post new topic   Reply to topic    www.mcselec.com Forum Index -> BASCOM-ARDUINO All times are GMT + 1 Hour
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum