Author |
Message |
Topic: Problems with ATMEGA164PA |
madhav1080
Replies: 17
Views: 1091
|
Forum: BASCOM-AVR Posted: Sun May 13, 2018 10:28 am Subject: ATMEGA164 Timer0 issue & PCINT2 Problems |
Yes of course, I use Code Explorer, here is a screenshot from my computer...
Timer2 can be tested by assigning Del some value and calling an event like setting a port pin High or transmitting a kno ... |
Topic: Problems with ATMEGA164PA |
madhav1080
Replies: 17
Views: 1091
|
Forum: BASCOM-AVR Posted: Sun May 13, 2018 4:06 am Subject: ATMEGA164PA Timer2 & PCINT2 (pin change) interrupt issue |
Hello,
Since the Timer2 was not functional, I just modified the code to use Timer1, in this program. I am already using Timer0 for the 50Hz dimming using Zero cross hardware, Have no issues with Ti ... |
Topic: Problems with ATMEGA164PA |
madhav1080
Replies: 17
Views: 1091
|
Forum: BASCOM-AVR Posted: Sat May 12, 2018 9:26 am Subject: Problems with ATMEGA164PA |
Hello,
I have been using ATMEGA164PA since its launch in a Xbee to Modbus converters and must have delivered over 3000 units till date, in another of my products, a Home automation control for 4 re ... |
Topic: Problems with ATMEGA164PA |
madhav1080
Replies: 1
Views: 169
|
Forum: BASCOM-AVR Posted: Sat May 12, 2018 9:25 am Subject: Problems with ATMEGA164PA |
Hello,
I have been using ATMEGA164PA since its launch in a Xbee to Modbus converters and must have delivered over 3000 units till date, in another of my products, a Home automation control for 4 re ... |
Topic: LM75 sensor on different boards reads different temperatures |
madhav1080
Replies: 11
Views: 1955
|
Forum: Various Posted: Mon Nov 20, 2017 2:46 am Subject: LM75 sensor on different boards reads different temperatures |
Thank you for the prompt reply, will try with 4.7K and no series resistor, however i have been using this configuration of ages more than (15 years) without any issues, Oh yes i have multiple devices ... |
Topic: LM75 sensor on different boards reads different temperatures |
madhav1080
Replies: 11
Views: 1955
|
Forum: Various Posted: Sun Nov 19, 2017 5:08 pm Subject: LM75 sensor on different boards reads different temperatures |
Yes all Boards have ATMEGA32A and all boards are running the same software.
The Board is my own design as requested I have attached the Schematic here, as had informed earlier, the LM75 is soldered o ... |
Topic: LM75 sensor on different boards reads different temperatures |
madhav1080
Replies: 11
Views: 1955
|
Forum: Various Posted: Wed Nov 15, 2017 2:59 am Subject: lm75 isssue, same devuce on multiple boards |
Sorry was away, couldn't reply back earlier....
Yes it is one Lm75 mounted on a smt to dip conversion pcb connected to different microcontroller boards, shows different temperatures.
Yes have a ... |
Topic: LM75 sensor on different boards reads different temperatures |
madhav1080
Replies: 11
Views: 1955
|
Forum: Various Posted: Tue Nov 07, 2017 8:54 am Subject: LM75 sensor on different boards reads different temperatures |
Hello,
I am using a LM75 i2c temperature sensor in an application running on ATMEGA32A running at 16MHz.
I have noticed that the same sensor when plugged into different production boards reports ... |
Topic: Problem with i2c (Software i2c on TWI pins M88PA) |
madhav1080
Replies: 2
Views: 260
|
Forum: BASCOM-AVR Posted: Mon Jun 15, 2015 11:44 am Subject: Problem with i2c (Software i2c on TWI pins M88PA) |
Yes, the problem was with the MOTOR, funny why the I2Cstop does not get executed causing the program to hang. |
Topic: Problem with i2c (Software i2c on TWI pins M88PA) |
madhav1080
Replies: 2
Views: 260
|
Forum: BASCOM-AVR Posted: Mon Jun 15, 2015 11:32 am Subject: Problem with i2c (Software i2c on TWI pins M88PA) |
Having a funny problem, I am using a in house developed General purpose M88 board, the I2C bus is connected to the hardware I2C Port on M88PA i.e SDA PORTC.4 & SCL PORTC.5, The program is getting ... |
Topic: ATMEGA128A Timer problem |
madhav1080
Replies: 0
Views: 157
|
Forum: BASCOM-AVR Archive Posted: Tue Oct 16, 2012 6:37 am Subject: ATMEGA128A Timer problem |
Hello,
I use ATMEGA128 in my product, at boot up the system starts a clock (count down timer) implimented using onboard timers. This code was developed in 2003 and was running fine till i upgraded ... |
Topic: Possible Bug with LookupStr |
madhav1080
Replies: 5
Views: 658
|
Forum: BASCOM-AVR Archive Posted: Mon Apr 26, 2010 7:13 pm Subject: Possible Bug with LookupStr |
At Powerup if user presses INCSW the System is supposed to execute...
If Incsw = 0 Then
Call Setup_opmode
End If
This actually opens up two options, Setup_opmode uses lookupstr to disp ... |
Topic: Possible Bug with LookupStr |
madhav1080
Replies: 5
Views: 658
|
Forum: BASCOM-AVR Archive Posted: Wed Apr 21, 2010 9:20 am Subject: Possible Bug with LookupStr |
Thank you for the reply
That was the first thing I tried, the problem still exists |
Topic: Possible Bug with LookupStr |
madhav1080
Replies: 5
Views: 658
|
Forum: BASCOM-AVR Archive Posted: Mon Apr 19, 2010 4:46 pm Subject: Possible Bug with LookupStr |
My code writen about 2 years stopped working properly in the curent version 1.11.9.8 However when compiled on 1.11.8.8 is working perfectly.
'######################################################### ... |
Topic: Strange problem with interrupts |
madhav1080
Replies: 3
Views: 637
|
Forum: BASCOM-AVR Archive Posted: Tue Oct 27, 2009 6:12 pm Subject: Strange problem with interrupts |
Well this is to control a very complex gas control system I use the latest version i.e 1.11.9.5, The code is very very large am unable to attach it here |
|