Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Search found 121 matches
www.mcselec.com Forum Index
Author Message
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Fri Aug 14, 2020 10:03 am   Subject: Clock frequency
Well, it's also interesting that he doesn't remember the manual correction after the restart, even though they write in the data sheet that they do.
I just sent how it can be changed, now I'm prepari ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Thu Aug 13, 2020 2:50 pm   Subject: Clock frequency
So setting the OSC20MCALIBA register and thus the frequency of the oscillator is simple.
If someone needs it, it can be done like this in bascom (this will raise the frequency from the company's 19.6 ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Thu Aug 13, 2020 9:05 am   Subject: Clock frequency
I understood what you meant, just a little later than usual. Smile
I will try the dependence of the frequency on the supply voltage of what it actually does. My point is that you actually calculate all ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Wed Aug 12, 2020 8:34 pm   Subject: Clock frequency
I'm sorry I translated it and understood if someone read what was here.

It will be because there are actually 4 options (2 bits) and here are 5 options, so you have no way to handle it. I forgot th ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Wed Aug 12, 2020 2:28 pm   Subject: Clock frequency
She is not a mistake according to the help there is only a 20mhz option. That's why I asked if it was not supported. But I know about switching fuses, but if you need to set up a prescaler, the choice ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Wed Aug 12, 2020 8:36 am   Subject: Clock frequency
Hello Mark
I am aware that this is not a support point for the system, but since I have experienced that a lot of people run into the same problem and then solve the same thing unnecessarily and over ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Tue Aug 11, 2020 11:50 am   Subject: Clock frequency
However, I wrote in the message above that the value in the calibration register does not correspond to what they have stored there and that it will probably be some strange.
That's why I put a list ...
  Topic: PWM & xtiny (ATTINY3217)
SZTRAD

Replies: 14
Views: 651

PostForum: BASCOM-AVR   Posted: Tue Aug 11, 2020 11:46 am   Subject: PWM & xtiny (ATTINY3217)
I probably don't understand what you're talking about, but the advantage of Bascom and its biggest advantage is that you don't really have to change anything and adjust it manually. The environment wi ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Tue Aug 11, 2020 11:17 am   Subject: Clock frequency
The value of 9E is 8bit right? The actual value is 1E, 8 and 7 bits you have to mask.
Based on FREQSEL in FUSE.OSCCFG, you only select the fundamental frequency. The calibration is taken from the CLK ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Tue Aug 11, 2020 10:21 am   Subject: Clock frequency
1317/5000
Hi
An external crystal is the solution but it takes up input and they are extra components.
I took a clean, unused 1604 chip and had the constants listed after a reboot.
This is the resu ...
  Topic: Clock frequency
SZTRAD

Replies: 25
Views: 1103

PostForum: BASCOM-AVR   Posted: Mon Aug 10, 2020 4:02 pm   Subject: Clock frequency
So one solution, I continue.
Mark, do you take into account the calibration constants of the internal RC oscillator to generate the baud rate?
What is my point? The test chip with which I test the p ...
  Topic: ADC xttiny
SZTRAD

Replies: 12
Views: 828

PostForum: BASCOM-AVR   Posted: Sun Aug 09, 2020 11:10 am   Subject: ADC xttiny
So I tried differently and unfortunately I have to say that it works for them. I'll have to explore Bascom and the features in the data entry file. This is an extract from Arduino's place setting and ...
  Topic: ADC xttiny
SZTRAD

Replies: 12
Views: 828

PostForum: BASCOM-AVR   Posted: Fri Aug 07, 2020 5:57 am   Subject: ADC xttiny
We'll see
By the way, one of the reasons why I used to reach for AVR after 8051 and not PIC were catalog sheets. The microchip has always been confused.
Otherwise, I modified the DAT files, but the ...
  Topic: ADC xttiny
SZTRAD

Replies: 12
Views: 828

PostForum: BASCOM-AVR   Posted: Thu Aug 06, 2020 5:19 pm   Subject: ADC xttiny
I'm a lot confused.
When I look at atmelstudio, prodsig_address is 1103 for chips, for example 1604.06 and 816

<memory-segment exec="0" name="EEPROM" pagesize="0x20" rw="RW" size="0x0080" start ...
  Topic: NEW PAID VERSION OF BASCOM TO SUPPORT NEW MICROCONTROLLERS
SZTRAD

Replies: 35
Views: 3938

PostForum: BASCOM-AVR   Posted: Thu Aug 06, 2020 11:56 am   Subject: NEW PAID VERSION OF BASCOM TO SUPPORT NEW MICROCONTROLLERS
For me, a number of xttinys are ok, except for some slight differences that can be bypassed ASM. The advantage of complex Bascom functions and ease of programming was the reason why I once bought it. ...
 
Page 7 of 9 Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8, 9  Next
All times are GMT + 1 Hour
Jump to: