Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Search found 56 matches
www.mcselec.com Forum Index
Author Message
  Topic: Bascom ADXL345 via IC -no response by device
autoguider

Replies: 2
Views: 220

PostForum: BASCOM-AVR   Posted: Fri Sep 27, 2019 2:20 pm   Subject: Bascom ADXL345 via IC -no response by device
Dear all,
I do my first steps with IC on Bascom so it may be that I do not see the trees because of the forest.
I want to run a ADXL345 accelerometer via IC.
The accelerometer is on a breakout bo ...
  Topic: Bascom Terminal Emulator malfunction ? Win 10 ?
autoguider

Replies: 9
Views: 472

PostForum: BASCOM-AVR   Posted: Thu Sep 12, 2019 10:51 pm   Subject: Bascom Terminal Emulator malfunction ? Win 10 ?
I have the blue background color.
In the window I do not see the data sent from the MCU
There is a vertical yellow line on the right hand side of the terminal emulator window e.g. after clearing the ...
  Topic: HC-SR04 on 328p
autoguider

Replies: 8
Views: 495

PostForum: BASCOM-AVR   Posted: Thu Sep 12, 2019 10:20 pm   Subject: HC-SR04 on 328p
!in r16, PIND hat geholfen
  Topic: HC-SR04 on 328p
autoguider

Replies: 8
Views: 495

PostForum: BASCOM-AVR   Posted: Thu Sep 12, 2019 10:14 pm   Subject: HC-SR04 on 328p
Thanks for the advice.
What do you recommend to read the status of the pin ?

BR
Ch.
  Topic: Bascom Terminal Emulator malfunction ? Win 10 ?
autoguider

Replies: 9
Views: 472

PostForum: BASCOM-AVR   Posted: Wed Sep 11, 2019 9:54 pm   Subject: Bascom Terminal Emulator malfunction ? Win 10 ?
Dear All,
I cannot get the build in Terminal emulator operating. I am running a 328 p on an Arduino UNO R3 hardware environment. I removed the Arduino bootloader and installed the MCS. Running very w ...
  Topic: HC-SR04 on 328p
autoguider

Replies: 8
Views: 495

PostForum: BASCOM-AVR   Posted: Wed Sep 11, 2019 9:37 pm   Subject: HC-SR04 on 328p
many thanks for your replies.
As you may see I modified the code using your advice.

$lib "mcs.lbx"
$regfile = "m328pdef.dat" ' Specify The Used Micro " ...
  Topic: HC-SR04 on 328p
autoguider

Replies: 8
Views: 495

PostForum: BASCOM-AVR   Posted: Fri Sep 06, 2019 2:40 pm   Subject: HC-SR04 on 328p
So there may be a systematic error in the measurement.
I was searching in the internet but it is still not clear to me.

Thanks for the advice with the timer.
Then I can understand why I receive t ...
  Topic: HC-SR04 on 328p
autoguider

Replies: 8
Views: 495

PostForum: BASCOM-AVR   Posted: Fri Sep 06, 2019 12:23 am   Subject: HC-SR04 on 328p
Dear all,
I want to measure a distance in the range < 1m. Accuracy is not the issue.
The hardware is a 328p on Arduino board
My idea is to use Timer 1 to measure the length of the echo signal. ...
  Topic: Bootloader in bascom for Arduino UNO R3
autoguider

Replies: 2
Views: 381

PostForum: BASCOM-ARDUINO   Posted: Mon Sep 02, 2019 10:56 pm   Subject: Bootloader in bascom for Arduino UNO R3
I decided to install the MCS bootloader on a 328p on my programming board and then put this 328p on the Arduino board.
Bootloader did not run.

I programmed it with a 16 MHz crystal.
For the MCS b ...
  Topic: Bootloader in bascom for Arduino UNO R3
autoguider

Replies: 2
Views: 381

PostForum: BASCOM-ARDUINO   Posted: Mon Aug 26, 2019 10:44 pm   Subject: Bootloader in bascom for Arduino UNO R3
Dear all.
I made my first experience with Arduino and Bascom.
Uploading of the program went well for 6 times. There was an alert message that the loader could not write the fuses. To my opinion this ...
  Topic: Program seems to reboot itself
autoguider

Replies: 7
Views: 403

PostForum: BASCOM-AVR   Posted: Fri Sep 28, 2018 11:04 am   Subject: Program seems to reboot itself
Many thanks for the advice.
I modified the ISR with saving the X register.
I also changed the UART to non buffered in both directions. Communication to the PC via RS232 runs well.

best regards
C ...
  Topic: Program seems to reboot itself
autoguider

Replies: 7
Views: 403

PostForum: BASCOM-AVR   Posted: Thu Sep 27, 2018 10:00 pm   Subject: Program seems to reboot itself
Dear All,
thanks for replying.
I installed the pull-up resistor on the evaluation board. It will definetely help to have clear conditions on the board.
In the meantime i did some research and fou ...
  Topic: Program seems to reboot itself
autoguider

Replies: 7
Views: 403

PostForum: BASCOM-AVR   Posted: Tue Sep 25, 2018 5:32 pm   Subject: Program seems to reboot itself
Hi Ian,
here the data;
$lib "mcs.lbx"
$regfile = "m168def.dat"
$prog &HFF , &HE7 , &HDF , &HF8 ' generated. Take care that the chip supports all fuse bytes. ...
  Topic: Program seems to reboot itself
autoguider

Replies: 7
Views: 403

PostForum: BASCOM-AVR   Posted: Tue Sep 25, 2018 2:54 pm   Subject: Program seems to reboot itself
Dear All,
I found the strange behaviour in my program that I experience the first time.

The C is a AVR 168 @ 6.144 MHz running on a Pollin evaluation board. External power supply.
Rectifier is o ...
  Topic: Program does not start when uploaded via bootloader
autoguider

Replies: 31
Views: 1602

PostForum: BASCOM-AVR Unsupported versions   Posted: Sun May 27, 2018 3:03 pm   Subject: Program does not start when uploaded via bootloader
Next addition and dscovery:

it works when bootloader and application are compiled with the identical values of $baud .
My application runs on 19200 Baud and the bootloader was compiled to operate ...
 
Page 1 of 4 Goto page 1, 2, 3, 4  Next
All times are GMT + 1 Hour
Jump to: