Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Search found 68 matches
www.mcselec.com Forum Index
Author Message
  Topic: CAN-bus library for general CAN-bus controller chip MCP2515
andro

Replies: 21
Views: 2628

PostForum: Share your working BASCOM-AVR code here   Posted: Fri Feb 07, 2020 1:05 pm   Subject: CAN-bus library for general CAN-bus controller chip MCP2515
That would be a major change of the concept. First I would start as it is - without INT / ISR handling.
I already prepared some HW
BR
A
  Topic: CAN-bus library for general CAN-bus controller chip MCP2515
andro

Replies: 21
Views: 2628

PostForum: Share your working BASCOM-AVR code here   Posted: Thu Feb 06, 2020 10:57 pm   Subject: CAN-bus library for general CAN-bus controller chip MCP2515
Hi Per,

It seems to me, You do not use INT pin (from MCP2515). Is that correct?

BR
Andrej
  Topic: CAN-bus library for general CAN-bus controller chip MCP2515
andro

Replies: 21
Views: 2628

PostForum: Share your working BASCOM-AVR code here   Posted: Thu Feb 06, 2020 9:30 pm   Subject: CAN-bus library for general CAN-bus controller chip MCP2515
Hello!

Yes, Mark, I'll do as You suggested. Now I also see it is an .inc file, not a .lib, so the workaround is (for me) much simpler.
As far as I have 'investigated' in last few minutes, I (only) ...
  Topic: CAN-bus library for general CAN-bus controller chip MCP2515
andro

Replies: 21
Views: 2628

PostForum: Share your working BASCOM-AVR code here   Posted: Thu Feb 06, 2020 7:41 pm   Subject: CAN-bus library for general CAN-bus controller chip MCP2515
Hi
The major difference is in "SPI".
Therefore I would have to change the part off the library where SPI is actually in use.
Is it ok, if I try to change your lib?
Br
Andrej
  Topic: CAN-bus library for general CAN-bus controller chip MCP2515
andro

Replies: 21
Views: 2628

PostForum: Share your working BASCOM-AVR code here   Posted: Thu Feb 06, 2020 12:12 pm   Subject: CAN-bus library for general CAN-bus controller chip MCP2515
Hi,

That's realy great job!
Question: does this library support Xmega familly?
Br
Andrej
  Topic: Problem Including Bootloader Code in Application Program
andro

Replies: 27
Views: 2905

PostForum: BASCOM-AVR   Posted: Thu Dec 12, 2019 10:24 pm   Subject: Problem Including Bootloader Code in Application Program
Thanks Neil.

When I'll have time to 'play' with this issue I will make a post. It might be interesting also for others.

BR

Andrej
  Topic: Problem Including Bootloader Code in Application Program
andro

Replies: 27
Views: 2905

PostForum: BASCOM-AVR   Posted: Thu Dec 12, 2019 7:14 am   Subject: Problem Including Bootloader Code in Application Program
Hello

Thanks for the answer. Did You try it also with Xmega ?

BR
andrej
  Topic: Problem Including Bootloader Code in Application Program
andro

Replies: 27
Views: 2905

PostForum: BASCOM-AVR   Posted: Wed Nov 27, 2019 10:40 pm   Subject: Problem Including Bootloader Code in Application Program
Hello Neil,

does Your bootloader work or not?

BR
Andrej
  Topic: I think, Config TCP is not confortable with W5500
andro

Replies: 22
Views: 1739

PostForum: EASY TCP/IP   Posted: Sat Jul 20, 2019 11:00 pm   Subject: I think, Config TCP is not confortable with W5500
Hi,

MAC addresses are ok. (also the MSB octet an even number).
Modules were bougth at TME and I believe, they are all genuine. Yes, I tried also some aliexpress modules - they seem to be fake ind ...
  Topic: I think, Config TCP is not confortable with W5500
andro

Replies: 22
Views: 1739

PostForum: EASY TCP/IP   Posted: Fri Jul 19, 2019 9:38 pm   Subject: I think, Config TCP is not confortable with W5500
Hello!

I use a wiz850 module for a simple tcp communication with servers. I did not mess any buffer settings or something. I only open one socket, establish tcp session and maintain it with periodi ...
  Topic: mega16m1 + Config CANbusmode
andro

Replies: 2
Views: 193

PostForum: BASCOM-AVR   Posted: Tue Jun 18, 2019 9:29 pm   Subject: mega16m1 + Config CANbusmode
Thanks for the answer.

Best regards
Andrej
  Topic: mega16m1 + Config CANbusmode
andro

Replies: 2
Views: 193

PostForum: BASCOM-AVR   Posted: Tue Jun 18, 2019 2:04 pm   Subject: mega16m1 + Config CANbusmode
Hi!

Does Bascom support CAN commands with ATmega16m1 ?

(I know - there is a note at the Config Canbusmode help: "The CAN commands are intended for the AVR processor AT90CANXXX series"....)

...
  Topic: I think, Config TCP is not confortable with W5500
andro

Replies: 22
Views: 1739

PostForum: EASY TCP/IP   Posted: Thu May 16, 2019 10:20 am   Subject: I think, Config TCP is not confortable with W5500
Hello to all!

I still have problems with w5500 ...
katipefendi, six1 - what is your experience with w5500 now, after almost a year after last post?

br
andrej
  Topic: w5500 problems
andro

Replies: 0
Views: 222

PostForum: BASCOM-AVR   Posted: Thu May 16, 2019 7:47 am   Subject: w5500 problems
Hello!

I use wiz850io modules with xmega256a3u. My app connects to a server, listening at 8013 port. A special 'protocol' to transfer data and maintain TCP session is made. Everything works fine, b ...
  Topic: Xmega HID host
andro

Replies: 5
Views: 424

PostForum: BASCOM-AVR   Posted: Wed Feb 27, 2019 1:13 am   Subject: Xmega HID host
Hi

Thanks to all for the answers.
After Mark explained, that xmega does not support host mode, I took a look at those vnc1/vnc2 by ftdi.
But now I read, you have had bad experiences with it.
How ...
 
Page 1 of 5 Goto page 1, 2, 3, 4, 5  Next
All times are GMT + 1 Hour
Jump to: