Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Search found 67 matches
www.mcselec.com Forum Index
Author Message
  Topic: Bascom 2083
Robert_d1968

Replies: 12
Views: 706

PostForum: BASCOM-AVR   Posted: Sat Apr 17, 2021 3:38 am   Subject: Bascom 2083
Hello there,

I did contact support and I now have the newest version out.

But it does not run on my laptop on windows 10.

So I'm going to try to install with wine under Ubuntu Linux and see i ...
  Topic: Bascom 2083
Robert_d1968

Replies: 12
Views: 706

PostForum: BASCOM-AVR   Posted: Sun Apr 11, 2021 10:53 pm   Subject: Bascom 2083
I have tried to update my version to the latest version, but it just stops responding in windows 10.

And I do have a valid license for that version, that I'm using now

Robert
  Topic: Bascom 2083
Robert_d1968

Replies: 12
Views: 706

PostForum: BASCOM-AVR   Posted: Sun Apr 11, 2021 9:13 am   Subject: Bascom 2083
Hello there it has been a while since I have been on the forum here. But I did notice a post about version 2083, and I would like to know
Where I can purchase this from?

I also noticed a forum for ...
  Topic: Help with sending inputs to serial port
Robert_d1968

Replies: 4
Views: 461

PostForum: BASCOM-AVR   Posted: Tue Apr 03, 2018 4:06 pm   Subject: Help with sending inputs to serial port
@ albertsm

Yes I see your point, I have not looked at the newest documents, my bad on that one.

But a little code example would have been better than the explanation given.

There are still li ...
  Topic: Help with sending inputs to serial port
Robert_d1968

Replies: 4
Views: 461

PostForum: BASCOM-AVR   Posted: Tue Apr 03, 2018 2:18 pm   Subject: Help with sending inputs to serial port
Hello everybody,

I'm currently trying to send from an ATMEGA8L to a terminal program the input status of all inputs on the ATMEGA8L to that terminal.

I have set the communication specs to 115200 ...
  Topic: ATmega88 and adc problem *SOLVED*
Robert_d1968

Replies: 5
Views: 351

PostForum: BASCOM-AVR   Posted: Sun Jan 08, 2017 11:16 am   Subject: ATmega88 and adc problem *SOLVED*
Thanks for the pointer,

I did check the datasheet and you are correct. Sad

I guess I will just switch to the atmega128 instead, as I still need a lil more I/O.

Thanks for the help,

Rober ...
  Topic: ATmega88 and adc problem *SOLVED*
Robert_d1968

Replies: 5
Views: 351

PostForum: BASCOM-AVR   Posted: Sun Jan 08, 2017 10:15 am   Subject: ATmega88 and adc problem *SOLVED*
Hello everybody,

I'm using an ATmega88 for debug reasons (OCD). I set up the ADC to have one output PORTC.7 and one input on PORTC.2

The rest of portc is used for ADC readings.

Config Portb.6 ...
  Topic: Non Linear LED and PWM
Robert_d1968

Replies: 11
Views: 686

PostForum: BASCOM-AVR   Posted: Wed Nov 02, 2016 8:56 pm   Subject: Non Linear LED and PWM
Yes on the right track, it reads the right way.

As for dividing by 4 it's not needed, as the adc and pwm are both 10 bit.

It works well thus far in the debugger, tomorrow I will test it out on t ...
  Topic: Non Linear LED and PWM
Robert_d1968

Replies: 11
Views: 686

PostForum: BASCOM-AVR   Posted: Wed Nov 02, 2016 10:17 am   Subject: Non Linear LED and PWM

Calc_adc = end_adc - Start_adc
Calc_adc = Start_adc / Calc_adc


Setpoint = Setpoint / Calc_adc
if setpoint < Start_Adc then
Setpoint = Setpoint + Start_adc
else
...
  Topic: Non Linear LED and PWM
Robert_d1968

Replies: 11
Views: 686

PostForum: BASCOM-AVR   Posted: Tue Nov 01, 2016 3:56 pm   Subject: Non Linear LED and PWM
Dim Current_val As Word '- Current sensor reading
Dim Setpoint As Word '- Holds our Thumb-wheel setpoint
Dim Start_adc As W ...
  Topic: Non Linear LED and PWM
Robert_d1968

Replies: 11
Views: 686

PostForum: BASCOM-AVR   Posted: Tue Nov 01, 2016 2:47 pm   Subject: Non Linear LED and PWM
Thank-you for the clarification,

I'll give it a go..

By the way, your signature is quite cool, ingenues

Robert
  Topic: Non Linear LED and PWM
Robert_d1968

Replies: 11
Views: 686

PostForum: BASCOM-AVR   Posted: Tue Nov 01, 2016 2:22 pm   Subject: Non Linear LED and PWM
Just to make sure I got this right:


int start_adc = 512
int end_adc = 1023

float calc_adc = start_adc / (end_adc - start_adc)

out_adc = ( getadc(0) / calc_adc) + start_adc

int is an ...
  Topic: Non Linear LED and PWM
Robert_d1968

Replies: 11
Views: 686

PostForum: BASCOM-AVR   Posted: Tue Nov 01, 2016 1:39 pm   Subject: Non Linear LED and PWM
Hello everybody,

I'm trying to control an LED's brightness via PWM, simple job I would think.

An AT Mega 8a is being used in this project along with an LTC6102 current monitor. the problem lies ...
  Topic: FT800
Robert_d1968

Replies: 53
Views: 5399

PostForum: BASCOM-AVR   Posted: Sat Feb 28, 2015 12:50 pm   Subject: FT800
Thank you guys,

I have been working with the FT800 and the STM32F407 series of MCU's.

I was wondering if Bascom would put this together, Now that you have I would like to get the beta release fo ...
  Topic: HHO Generator
Robert_d1968

Replies: 13
Views: 2150

PostForum: BASCOM Project Blog   Posted: Fri Aug 22, 2014 6:43 pm   Subject: HHO Generator
This is the Board I intend to use to run the project, It's a 4 layer board and was built in about 5 hours of time.
If all works out, I will upload the board, schematics and artwork.
 
Page 1 of 5 Goto page 1, 2, 3, 4, 5  Next
All times are GMT + 1 Hour
Jump to: