Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Search found 58 matches
www.mcselec.com Forum Index
Author Message
  Topic: Why does MCS Bootloader contain a trojan?
POTOOLE64BAS

Replies: 23
Views: 4672

PostForum: Various   Posted: Thu Feb 19, 2009 4:38 am   Subject: Why does MCS Bootloader contain a trojan?
p2otoole@yahoo.com
  Topic: Programming atmega via USB, is a bootloader needed?
POTOOLE64BAS

Replies: 3
Views: 662

PostForum: BASCOM-AVR Archive   Posted: Tue Feb 17, 2009 6:20 am   Subject: Programming atmega via USB, is a bootloader needed?
Thanks for the information, guys.

PO'T
  Topic: Why does MCS Bootloader contain a trojan?
POTOOLE64BAS

Replies: 23
Views: 4672

PostForum: Various   Posted: Tue Feb 17, 2009 6:11 am   Subject: Why does MCS Bootloader contain a trojan?
I appreciate the offer Frankeman, but it appears that there is no way to get your email on this board. I tried to send a private message by clicking on PM, and get this response.

www.mcselec.com F ...
  Topic: Why does MCS Bootloader contain a trojan?
POTOOLE64BAS

Replies: 23
Views: 4672

PostForum: Various   Posted: Mon Feb 16, 2009 8:12 pm   Subject: Why does MCS Bootloader contain a trojan?
I download MCS Bootloader zip file, then tried to extract the files, but windows blocked them, because of the inclusion of a trojan.
So I had McAfee scan the zipped file, and McAfee also detected a ...
  Topic: Programming atmega via USB, is a bootloader needed?
POTOOLE64BAS

Replies: 3
Views: 662

PostForum: BASCOM-AVR Archive   Posted: Mon Feb 16, 2009 6:10 pm   Subject: Programming atmega via USB, is a bootloader needed?
How can an atmega chip be programmed by the use of USB connections from a laptop?
Is a pre-programmed bootloader necessary?

Thanks
  Topic: Using Interrupts, where and why?
POTOOLE64BAS

Replies: 1
Views: 774

PostForum: Various   Posted: Wed Feb 11, 2009 6:32 am   Subject: Using Interrupts, where and why?
What is the importance of using interrupts?
When and why should they be used?
If a code works without using or enableing interrupts, is that a bad thing?

Should interrupts be used in the followin ...
  Topic: Communication with Terminal emulator
POTOOLE64BAS

Replies: 25
Views: 1931

PostForum: BASCOM-AVR Archive   Posted: Sun Feb 08, 2009 6:36 pm   Subject: Communication with Terminal emulator
I can't offer much advice, since I'm very new with this stuff. The advice of the previous repliers have much more to offer than I can possibly do. I've never used an STK500 setup, and the question t ...
  Topic: Beginner help with Serial communication
POTOOLE64BAS

Replies: 11
Views: 1580

PostForum: BASCOM-AVR Archive   Posted: Sun Feb 08, 2009 8:57 am   Subject: Beginner help with Serial communication
Are you communicating with your PC by using a serial connection from your atmega chip to the serial port of the PC? Here's an example of what I have for that purpose, its a TTL to RS232 converter asse ...
  Topic: How to deal with the innacuracy of "WAIT" command?
POTOOLE64BAS

Replies: 5
Views: 1242

PostForum: BASCOM-AVR Archive   Posted: Fri Feb 06, 2009 7:21 am   Subject: How to deal with the innacuracy of "WAIT" command?
From AdrianJ
FrameTimeout alias TIFR.OCF1A 'meaningful name
Const FrameDelay = 500 ' some number you set
'of course you also have to set the timer prescaler,
and start the timer.
[i]& ...
  Topic: How to deal with the innacuracy of "WAIT" command?
POTOOLE64BAS

Replies: 5
Views: 1242

PostForum: BASCOM-AVR Archive   Posted: Thu Feb 05, 2009 11:00 pm   Subject: How to deal with the innacuracy of "WAIT" command?
Thanks everybody, I'll need to spend some time studying the situation.
In other words I gotta figure out what all this means; its a little new for this old dude. Lots of acronyms to look up.

The ...
  Topic: How to deal with the innacuracy of "WAIT" command?
POTOOLE64BAS

Replies: 5
Views: 1242

PostForum: BASCOM-AVR Archive   Posted: Thu Feb 05, 2009 7:00 am   Subject: How to deal with the innacuracy of "WAIT" command?
From Bascom-AVR help file

WAIT
Action: Suspends program execution for a given time

Syntax
WAIT seconds

Remarks: seconds = The number of seconds to wait.

No accurate timing is possible wi ...
  Topic: Why do I get this? COULD NOT IDENTIFY CHIP WITH ID:FFFFFF.
POTOOLE64BAS

Replies: 15
Views: 2475

PostForum: BASCOM-AVR Archive   Posted: Tue Feb 03, 2009 7:27 pm   Subject: Why do I get this? COULD NOT IDENTIFY CHIP WITH ID:FFFFFF.
Thank you, tasosstr, I will try that too.
I haven't worked on this problem for a couple of days.

Patrick
  Topic: Where can I buy an Atmega168 that can be pgmd. with Bascom?
POTOOLE64BAS

Replies: 17
Views: 2051

PostForum: BASCOM-AVR Archive   Posted: Sun Feb 01, 2009 11:56 pm   Subject: Where can I buy an Atmega168 that can be pgmd. with Bascom?
ecoology said
I use both the M168, and M168P. For programming, I use Studio 4 - a free programming platform from Atmel. Try using Bascom to generate the .hex file, than programming from Studio.

I ...
  Topic: Why do I get this? COULD NOT IDENTIFY CHIP WITH ID:FFFFFF.
POTOOLE64BAS

Replies: 15
Views: 2475

PostForum: BASCOM-AVR Archive   Posted: Sun Feb 01, 2009 7:44 pm   Subject: Why do I get this? COULD NOT IDENTIFY CHIP WITH ID:FFFFFF.
Thanks everybody for all the information.
I printed the info. out so that I can use it when I'm ready.

Patrick
  Topic: Why do I get this? COULD NOT IDENTIFY CHIP WITH ID:FFFFFF.
POTOOLE64BAS

Replies: 15
Views: 2475

PostForum: BASCOM-AVR Archive   Posted: Sun Feb 01, 2009 3:51 am   Subject: Why do I get this? COULD NOT IDENTIFY CHIP WITH ID:FFFFFF.
_________________________________________
1/31
Thank you ibilzh for the very descriptive information. I will give that a try. Looks like information that will work quite well. Thank you

STK5O ...
 
Page 1 of 4 Goto page 1, 2, 3, 4  Next
All times are GMT + 1 Hour
Jump to: