Author |
Message |
Topic: Starting Bootloader from Application |
Alex20q90
Replies: 3
Views: 2539
|
Forum: AVR Posted: Sat Mar 10, 2018 6:05 pm Subject: Re: Starting Bootloader from Application |
Hi,
Goto &Hxxx should work,
However &H1000 is not a valid Bootloader address, what is valid depends on how big your bootloader loader is, have a look at the
Thanks Evert!
I read it in ... |
Topic: Starting Bootloader from Application |
Alex20q90
Replies: 3
Views: 2539
|
Forum: AVR Posted: Sat Mar 10, 2018 12:02 pm Subject: Starting Bootloader from Application |
Hello,
i have a new problem! I use a ATMega8u2 mit LUFA Bootloader. In Bascom i can flash my Application with Bascom over the "FLIP"-Programmer directly via USB. It works.
If i would flash again, ... |
Topic: MTMega8u2 PWM on three Channels |
Alex20q90
Replies: 14
Views: 737
|
Forum: BASCOM-AVR Posted: Fri Mar 09, 2018 9:00 pm Subject: MTMega8u2 PWM on three Channels |
the timer registers are set correctly. but what is missing is the configuration of the pin to output. i have corrected this. if simply configuring the pins to output before the config timer command a ... |
Topic: MTMega8u2 PWM on three Channels |
Alex20q90
Replies: 14
Views: 737
|
Forum: BASCOM-AVR Posted: Mon Mar 05, 2018 9:00 am Subject: MTMega8u2 PWM on three Channels |
Hi MWS,
many thanks for help, but it dont work!
If i toggle by a selfmade soft-pwm, i can use all 3 outputs. I put RGB-LED on it to test.
Describe your dev-board, maybe PB7 is blocked or not ... |
Topic: MTMega8u2 PWM on three Channels |
Alex20q90
Replies: 14
Views: 737
|
Forum: BASCOM-AVR Posted: Sat Mar 03, 2018 8:15 pm Subject: Re: MTMega8u2 PWM on three Channels |
Hi MWS,
thanks for your help, but it dont work! Only chan 1 and 2.
Yes, because it dont work!
Nonsense, what kind of logic is this?
A compilable sample helps to have a look into the registers. ... |
Topic: MTMega8u2 PWM on three Channels |
Alex20q90
Replies: 14
Views: 737
|
Forum: BASCOM-AVR Posted: Sat Mar 03, 2018 12:08 pm Subject: Re: MTMega8u2 PWM on three Channels |
Any hint what i make wrong?
You haven't posted an compilable example.
Yes, because it dont work!
I tried:
$regfile ="M8u2def.dat"
$crystal = 8000000
Config Timer1 = Pwm , Pwm = ... |
Topic: MTMega8u2 PWM on three Channels |
Alex20q90
Replies: 14
Views: 737
|
Forum: BASCOM-AVR Posted: Fri Mar 02, 2018 5:49 pm Subject: MTMega8u2 PWM on three Channels |
Hi,
i try to use all three OC1x-Channels on the ATMega8u2.
But i can only
Config Timer1 = Pwm , Pwm = 8 , Compare A Pwm = Clear down , Compare B Pwm = Clear down , Prescale = 1
and
... |
Topic: Command line to write .hex with Bascom (programmer) |
Alex20q90
Replies: 11
Views: 664
|
Forum: BASCOM-AVR Posted: Fri Feb 09, 2018 11:41 am Subject: Command line to write .hex with Bascom (programmer) |
I did answer it, did you read and understand?
I think i dont understand!
In case you simply need a clear reply to above question: no, there is no Bascom command line to flash a controller, ... |
Topic: Command line to write .hex with Bascom (programmer) |
Alex20q90
Replies: 11
Views: 664
|
Forum: BASCOM-AVR Posted: Fri Feb 09, 2018 8:13 am Subject: Command line to write .hex with Bascom (programmer) |
ok, i ask different now:
is it possible to program a .hex file with bascom from command line? |
Topic: Command line to write .hex with Bascom (programmer) |
Alex20q90
Replies: 11
Views: 664
|
Forum: BASCOM-AVR Posted: Sun Feb 04, 2018 12:57 pm Subject: Command line to write .hex with Bascom (programmer) |
I think USB-Isp is a some kind of Atmel STK-200
You should try to install AVRDUDE and then from CMD -> avrdude -p atmega128 -c stk200 -P usb -V -U flash:w:"C:\test.hex":i -U lock:w:0x3C:m
uC ... |
Topic: Command line to write .hex with Bascom (programmer) |
Alex20q90
Replies: 11
Views: 664
|
Forum: BASCOM-AVR Posted: Sat Feb 03, 2018 6:51 pm Subject: Command line to write .hex with Bascom (programmer) |
you not understand!
no, i dont have the stk500 programmer! i have the mcs USB-ISP progI!
An i only have a .hex-File! I dont have a bascom .bas-File to compile!
I only need the "burning" funktio ... |
Topic: Command line to write .hex with Bascom (programmer) |
Alex20q90
Replies: 11
Views: 664
|
Forum: BASCOM-AVR Posted: Sat Feb 03, 2018 12:27 pm Subject: Command line to write .hex with Bascom (programmer) |
Hello,
i need help! I have a huge project and i need a command line (like avrdude) to say to my bascom "write .hex-File to AVR".
At moment i open the Writer-Tool, delete the Buffer, delete the A ... |
Topic: ATMega32u2 (32u4) with USB-Addon for Serial Transmission |
Alex20q90
Replies: 7
Views: 979
|
Forum: BASCOM-AVR Posted: Wed Jun 28, 2017 1:58 pm Subject: ATMega32u2 (32u4) with USB-Addon for Serial Transmission |
Ohh, thanks!
I will try it later! At moment, i connect my ft232 via wire to my board on a free pin to get dbg_messages.
The USB is with too mutch overhead!
Thank you for the example!
Okay. I ... |
Topic: ATMega32u2 (32u4) with USB-Addon for Serial Transmission |
Alex20q90
Replies: 7
Views: 979
|
Forum: BASCOM-AVR Posted: Wed Jun 28, 2017 9:34 am Subject: ATMega32u2 (32u4) with USB-Addon for Serial Transmission |
Hello EDC,
I have some succesfull projects because I like to read documentation Very Happy
Do you read USB.pdf comes with libraries?
Sorry, i didnt read carefully because thats not my work ... |
Topic: ATMega32u2 (32u4) with USB-Addon for Serial Transmission |
Alex20q90
Replies: 7
Views: 979
|
Forum: BASCOM-AVR Posted: Wed Jun 28, 2017 7:18 am Subject: ATMega32u2 (32u4) with USB-Addon for Serial Transmission |
Hi EDC,
i dont know where i have to put the transmitting routine! A 'Print "Test" ' dont work!
'------------------------------------------------------------------------------
' ... |
|