Forum - MCS Electronics

 

FAQFAQ SearchSearch RegisterRegister Log inLog in

Search found 25 matches
www.mcselec.com Forum Index
Author Message
  Topic: Atxtiny1616
2New

Replies: 2
Views: 258

PostForum: BASCOM-AVR   Posted: Sun May 09, 2021 7:21 am   Subject: ATxtiny1616
Hi Mark.
Thanks a lot. Good help.
  Topic: Atxtiny1616
2New

Replies: 2
Views: 258

PostForum: BASCOM-AVR   Posted: Sat May 08, 2021 5:59 pm   Subject: Atxtiny1616
Hi,
attached programme shows a lot off errors:

Error : 117 Line : 14 Unknown interrupt (BASCOM-AVR version : 2.0.8.3 )
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Wed Oct 19, 2016 3:15 pm   Subject: Attiny4313/Interrupt
Just to close this case. There was a problem with the DAT-file for 2313/4313.
If you want to use this chips make sure you got the right versions of the mentioned files.
Rgds. Peter
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Thu Jun 16, 2016 5:49 pm   Subject: Attiny4313/ Interrupts
You are right, I agree we don't understand each other very much.
I've just put a print routine in te ISR and set Sol01 to 30 and the printout counted "32" interrupts and "30" for a variable in the "D ...
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Tue Jun 14, 2016 7:59 pm   Subject: Attiny4313/ Interrupts
Sure, I have tried Fallig with the same result.
Even with Low Level all the signals are clear and stable, I have watch them on an Logic analliser.
I reinstalled the program on a second machine.... s ...
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Tue Jun 14, 2016 4:18 pm   Subject: Attiny4313/Interrupts
I've installed IDE-Version 2.0.7.9. 003 and the problems are still there. The installation of some print routines shows a difference between the number of "ISR"and "Do...Loops".
Am I the only one fac ...
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Tue Jun 14, 2016 1:30 pm   Subject: Attiny 4313/ Interrupt
Assuming the problems are much more deeper.
Tried just to add "Print Sol01" and I got strange error messages.
Error : 222 Line : 41 Illegal character [expected (, got '' [_PRDWORD]] , in Fi ...
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Tue Jun 14, 2016 12:17 pm   Subject: Attiny4313/ Interrupt
When deactivating Powerdown the simulation runs perfect the same under "run program".
Problems occour under single step and on the chip.
I tried to find out whether the Flags have an influence to th ...
  Topic: ATTiny4313/ Interrupt
2New

Replies: 10
Views: 528

PostForum: BASCOM-AVR   Posted: Mon Jun 13, 2016 1:17 pm   Subject: ATTiny4313/ Interrupt
Hi,
I'm faced with a nasty problem.
During simulation the courser jumps on the second Interrupt (INT=0) not to “loop” instead it jumps to “config powermode= Powerdown”. I know this problem from teh ...
  Topic: Attiny84/ PCINT1&2
2New

Replies: 4
Views: 206

PostForum: BASCOM-AVR Archive   Posted: Thu Dec 06, 2012 9:01 pm   Subject: Attiny84/ PCINT1&2
Hello Hubert,
Thanks for the prompt reply.
Unfortunately your proposal doesn't work too. Even the interupt INT0 doesn't react.
I understood from the manual the following:
Pin A7 is corresponding ...
  Topic: Attiny84/ PCINT1&2
2New

Replies: 4
Views: 206

PostForum: BASCOM-AVR Archive   Posted: Thu Dec 06, 2012 4:23 pm   Subject: Attiny84/ PCINT1&2
Hello,
Is there anyone who can advise me what's wrong with the attached code.
INT0 and PCINT1 working fine, not so PCINT0. PCINT0 isn't working at any A-Pins.
Putting a resistor in, PCINT0 work fi ...
  Topic: Attiny2313/ PortD
2New

Replies: 6
Views: 533

PostForum: BASCOM-AVR Archive   Posted: Mon Apr 18, 2011 7:18 pm   Subject: Attiny2313/ PortD
Ddrb = &B01011111
Ddrd = &B01110000
Portd.2 = 1 this set INT0 HIGH

but when you set Portd.6 high you RESET INT0 pullup
Try:
Ontick03:
Portd = &B01000100 ' PORTD.6 =1 AND INT0 ...
  Topic: Attiny2313/ PortD
2New

Replies: 6
Views: 533

PostForum: BASCOM-AVR Archive   Posted: Mon Apr 18, 2011 7:07 pm   Subject: Attiny2313/ PortD
Hi
Portd = &B01000000
This will set your PULLUP on INT0 to 0 !!! (portd.2)
Ddrd = &B01110000 and Portd.2 = 1 means Portd2 is Input and set high. Nevertheless I tried it without any succe ...
  Topic: Attiny2313/ PortD
2New

Replies: 6
Views: 533

PostForum: BASCOM-AVR Archive   Posted: Mon Apr 18, 2011 6:59 pm   Subject: Attiny2313/ PortD
Hi
About INT0 :
LOW LEVEL to generate an interrupt while the pin is held low. Holding the pin low will generate an interrupt over and over again.

FALLING to generate an interrupt on the falling e ...
  Topic: Attiny2313/ PortD
2New

Replies: 6
Views: 533

PostForum: BASCOM-AVR Archive   Posted: Mon Apr 18, 2011 4:55 pm   Subject: Attiny2313/ PortD
Hi,
I'm faced with a nasty little problem. As soon as the programme enters Portd= &B01000000 it jumps permanently between this line and the headline.
Who will give me support?
 
Page 1 of 2 Goto page 1, 2  Next
All times are GMT + 1 Hour
Jump to: